mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include "mbed.h"
#include "BLE.h"
#include "URIBeaconConfigService.h"
#include "DFUService.h"
#include "DeviceInformationService.h"
#include "ConfigParamsPersistence.h"

BLE ble;
URIBeaconConfigService *uriBeaconConfig;

/**
 * URIBeaconConfig service can operate in two modes: a configuration mode which
 * allows a user to update settings over a connection; and normal URIBeacon mode
 * which involves advertising a URI. Constructing an object from URIBeaconConfig
 * service sets up advertisements for the configuration mode. It is then up to
 * the application to switch to URIBeacon mode based on some timeout.
 *
 * The following help with this switch.
 */
static const int CONFIG_ADVERTISEMENT_TIMEOUT_SECONDS = 60;  // Duration after power-on that config service is available.
Ticker configAdvertisementTimeoutTicker;

/**
 * Stop advertising the UriBeaconConfig Service after a delay; and switch to normal URIBeacon.
 */
void timeout(void)
{
    Gap::GapState_t state;
    state = ble.getGapState();
    if (!state.connected) { /* don't switch if we're in a connected state. */
        uriBeaconConfig->setupURIBeaconAdvertisements();
        ble.gap().startAdvertising();

        configAdvertisementTimeoutTicker.detach(); /* disable the callback from the timeout Ticker. */
    }
}

/**
 * Callback triggered upon a disconnection event. Needs to re-enable advertisements.
 */
void disconnectionCallback(Gap::Handle_t handle, Gap::DisconnectionReason_t reason)
{
    ble.gap().startAdvertising();
}

int main(void)
{
    ble.init();
    ble.gap().onDisconnection(disconnectionCallback);

    /*
     * Load parameters from (platform specific) persistent storage. Parameters
     * can be set to non-default values while the URIBeacon is in configuration
     * mode (within the first 60 seconds of power-up). Thereafter, parameters
     * get copied out to persistent storage before switching to normal URIBeacon
     * operation.
     */
    URIBeaconConfigService::Params_t params;
    bool fetchedFromPersistentStorage = loadURIBeaconConfigParams(&params);

    /* Initialize a URIBeaconConfig service providing config params, default URI, and power levels. */
    static URIBeaconConfigService::PowerLevels_t defaultAdvPowerLevels = {-20, -4, 0, 10}; // Values for ADV packets related to firmware levels
    uriBeaconConfig = new URIBeaconConfigService(ble, params, !fetchedFromPersistentStorage, "http://developer.mbed.org", defaultAdvPowerLevels);
    if (!uriBeaconConfig->configuredSuccessfully()) {
        error("failed to accommodate URI");
    }
    configAdvertisementTimeoutTicker.attach(timeout, CONFIG_ADVERTISEMENT_TIMEOUT_SECONDS);

    // Setup auxiliary services to allow over-the-air firmware updates, etc
    DFUService dfu(ble);
    DeviceInformationService deviceInfo(ble, "ARM", "UriBeacon", "SN1", "hw-rev1", "fw-rev1", "soft-rev1");

    ble.gap().startAdvertising(); /* Set the whole thing in motion. After this call a GAP central can scan the URIBeaconConfig
                                   * service. This can then be switched to the normal URIBeacon functionality after a timeout. */

    while (true) {
        ble.waitForEvent();
    }
}